have fun
Statistics: Posted by nay-seven — 17 Oct 2013, 13:54
]]>
OH MY GODNESS !!!
can i invite you to some wiskey or vodka ?
or...
can i send you a pro+*ti*+te to suck your .. ? xD
ahahha
IS WORKING MAN !!! you are the bestttttttt !!
seriously thanks :rolleyes:
you saved my money !!! and my mixer !!
Statistics: Posted by Taysete_DJ — 17 Oct 2013, 12:30
]]>
Download
Statistics: Posted by nay-seven — 17 Oct 2013, 11:39
]]>
and about the lights i triyed sending the same value as the outputs in the same inputs arrays in the hid module
but that just make the outputs not avaible...
maybe i can just convert the midi input to Hid in the array input ? if then , what module you suggest me to use?
Im thinking to make a Toggle buttons to send Midi CC to use in my DAW and it will be nice if i can make the lights pop out when i press the buttons ON ...
Statistics: Posted by Taysete_DJ — 15 Oct 2013, 19:00
]]>
I tried using the module 1-X after reinstalling usine all went good now but the module 1-X doesent do what i need to do ...
I will try to explain better my problem ...
The required signal in deckadance must be a value between 0-127
the problem is the wheel of my gemini just keep jumping from 127 to 0 or from 0 to 127 (when reverse)
So if i turn my wheel right its just counting +1 , until 127 then starts to 0 again
and if i turn left is -1 val , until 0 then starts to 127
I need the wheel change to this way :
If i turn left i want to make -1 val message until 0 , then send -1 message , but stay in 0 val.
If i turn right , +1 val. , until 127 , then +1 , but stay in 127..
maybe there is some way to make a knob or something to just count when i go value up or down ( +1 or -1 ) and make a limitation=?
Or what can i do ?
This is my last problem with the wheel if you can help me i will not disturb you anymore .. heheh
I really appreaciatte your help , thank you so much
Statistics: Posted by Taysete_DJ — 11 Oct 2013, 20:56
]]>
i suppose the only you can remote your hardware is by midi..? for example val 13 is maybe the note 13 and 128 correspond to note OFF message
Best way is to use a mid create module to send message ( CC , note on/off ) and try different values ( no risk)
yes i use the Remote to send midi and LoopMidi to route midiBest way is to use a mid create module to send message ( CC , note on/off ) and try different values ( no risk)
okay i will test it out later and post back the results
thanks
Statistics: Posted by Taysete_DJ — 08 Oct 2013, 14:22
]]>
Statistics: Posted by nay-seven — 08 Oct 2013, 14:07
]]>
Im doing two versions for use two different type of midi outputs to work separately in FL and Deckadance
the one im doing for FL studio is quite different than the deckadance one witch i use for mixing songs etc
But in FL i use it for composing etc... so controls are diffferent for this one
Well i got an idea , i think (maybe) it will be possible using arrays inputs with usine to turn on/off the lights of my Gemini?
and also i want to know if experimenting with inputs this can be dangerous?
and ...
If the button Cue is for example Val 13 , 128 pression then , the input will be the same?
Thanks in advance , and im so so happy that i have a "new controller" xD
after 3 years that i got it and now seems a new machine
Statistics: Posted by Taysete_DJ — 08 Oct 2013, 13:54
]]>
that's why i propose you to read the patching tutorial...
chapter 2, you'll find something about a module named 1-X
I had a problem loading the 1-X module , and i messed up with it chapter 2, you'll find something about a module named 1-X
i have triyed loading several times the 1-X module , but i cant seem to get it to work , i think my Usine Installation is corrupted sience i have installed too many version in my pc and i mixed up the libraryes from old versions etc ...
I wont buy any new version (yet) as i dont have a good economic situation, so i must stay with the stuff i have...
So finnally with the wheel i didnt finish it , but i do a kind of "patch" , now with a knoob i can switch the code to turn the wheel up or down
but that isnt the plan ... i must fix it in a future...
Statistics: Posted by Taysete_DJ — 04 Oct 2013, 18:39
]]>
chapter 2, you'll find something about a module named 1-X
Statistics: Posted by nay-seven — 02 Oct 2013, 20:32
]]>
not easy to test without the machine , but you can limit the jog wheel action this way ?
when value is equal or superior to 255 i stop the flow, and same if value is inferior or equal to 0:
http://www.sensomusic.com/forums/upload ... values.png
IF i do as you say the wheel keeps going back ( in deckadance) so the jump is working thats a good find but now to fix it at all i need to add a conditional when value is equal or superior to 255 i stop the flow, and same if value is inferior or equal to 0:
http://www.sensomusic.com/forums/upload ... values.png
if value is increasing = send invert value
if value is decreasing = send normal val
Statistics: Posted by Taysete_DJ — 02 Oct 2013, 20:02
]]>
I think i need to change the value this way :not easy to test without the machine , but you can limit the jog wheel action this way ?
when value is equal or superior to 255 i stop the flow, and same if value is inferior or equal to 0:
http://www.sensomusic.com/forums/upload ... values.png
when it reaches 255 to start counting - 1
or when reach 0 to start counting +1
so i mean i dont want the jump from 0 to 255 or viceversa
i really need your help can you add a example into this project Gemini CTRL SIX Midi Driver Beta 1
Statistics: Posted by Taysete_DJ — 02 Oct 2013, 18:52
]]>
Statistics: Posted by nay-seven — 02 Oct 2013, 18:46
]]>
all the other things are working good
Except the Lights , im sure is possible also to make them work , but thats too much for me , im happy if all midi data work
Statistics: Posted by Taysete_DJ — 02 Oct 2013, 18:28
]]>
for the 2 jog wheel, best practice is to analyses the data incoming,, i suggest you to read the patching tutorial.
about the uploader here the help page in the tips section
Jog wheels actuates like that ;about the uploader here the help page in the tips section
If i turn Jog Right :
Whatever the value is ,the value starts counting up +1 value (0-255) Infinite loop (every time reaches 255 starts to 0 again)
If i turn left :
The same but inverse it counts -1 value
So if i use the wheel in Deckadance the wheel just keep going forward and backward in a infinite loop process no matter if turn left or right
thanks for your help , this wheel part seem to be hard to fix
Download the project Gemini CTRL SIX Midi Driver Beta 1 Problematic wheels are : PLATO A , PLATO B , TURNE ( Turntable A , B and Filebrowser)
Statistics: Posted by Taysete_DJ — 02 Oct 2013, 18:21
]]>
about the uploader here the help page in the tips section
Statistics: Posted by nay-seven — 02 Oct 2013, 13:46
]]>
I really don't understand your patch, here how i see the patch:
Download
when you receive the value 128, for example, the switch is ON and send a note ON message, when OFF its send a Note OFF message ( and each switch send a different note number no..?)
for the fader , i 've add a conversion example with the sub patch scale (modules /data/data manipulation) and this fader send a control change message
And please avoid those deposit files system with pub, use the forum uploader
sorry i have found out the problem of note OFF / ONDownload
when you receive the value 128, for example, the switch is ON and send a note ON message, when OFF its send a Note OFF message ( and each switch send a different note number no..?)
for the fader , i 've add a conversion example with the sub patch scale (modules /data/data manipulation) and this fader send a control change message
And please avoid those deposit files system with pub, use the forum uploader
It was the value of OFF and ON
on must be 1
off 0
i still having a problem but now is just the wheel message , (the main two jog wheels for scratch)
but i hope it will be easy to fix out ,
Thanks so much for your help ! without your help this wasnt possible for me
PD : maybe is my internet explorer but i dont find the upload bar
Statistics: Posted by Taysete_DJ — 02 Oct 2013, 13:16
]]>
when you receive the value 128, for example, the switch is ON and send a note ON message, when OFF its send a Note OFF message ( and each switch send a different note number no..?)
for the fader , i 've add a conversion example with the sub patch scale (modules /data/data manipulation) and this fader send a control change message
And please avoid those deposit files system with pub, use the forum uploader
Statistics: Posted by nay-seven — 02 Oct 2013, 12:58
]]>
share image
here is the project http://dfiles.eu/files/1rr8f79gs
Statistics: Posted by Taysete_DJ — 02 Oct 2013, 11:40
]]>
Now i did some advances in my work , it will be a really nice mixer , but i still having 2 big problems ...
1 - doing buttons I can only seem to send Midi Note OFF messages only... i think i must add another send , but i dont know how to send note On , is not working
(i have tested Deckadance to use function buttons , but for example if i use CUE as only recieve note OFF is not working 100% ) i i think all buttons must be in toggle mode ... 2 - Jog Wheels are not sending the good parameter ( it sends an absolute CC between 0 - 255 ) but it must work as an ENCODER
I think after all help you giving to me , i must invite to all of you to a beer
I will try to upload my project here , also when finished , so anyone can use his Gemini's as a real midi controller , instead of terrible HID
Statistics: Posted by Taysete_DJ — 02 Oct 2013, 11:30
]]>
my mixer is saved to be on recicle byn
thanks NAY !
yeaah
Statistics: Posted by Taysete_DJ — 01 Oct 2013, 22:01
]]>
great news
and yes , most HID works this way, so you can use maths/logical modules like the A=B
here an example with your play switch:
http://www.sensomusic.com/forums/upload ... odules.png
Okay thaks so much! I was sure in time i can find a solution and yes , most HID works this way, so you can use maths/logical modules like the A=B
here an example with your play switch:
http://www.sensomusic.com/forums/upload ... odules.png
lets do some maths
xD
Statistics: Posted by Taysete_DJ — 01 Oct 2013, 21:42
]]>
and yes , most HID works this way, so you can use maths/logical modules like the A=B
here an example with your play switch:
Statistics: Posted by nay-seven — 01 Oct 2013, 20:33
]]>
Thanks for the software percuson, could be useful
and you're right about id number, that's why i ask to test all number from 0 to...
Hey NAY !! after long time ... THANKS AGAINand you're right about id number, that's why i ask to test all number from 0 to...
i figured out again how to solve this old problem .. and i tryed again this morning... i read again the whole post and tryed again all steps
And i got IT !!
The problem was i didnt seem to find the good ID
but now i did it !! ,, i can transform succesfully all faders , knobs , rotatorys and wheels to work as midi !!
but now i have a trouble to finish it ...
the buttons are the same value and there is just a Pression change , like this ;
Play , Pause , pitch bend, CUE, and Cue SET Buttons are the same HID value ,
CUE set 3 1
CUE set 2 2
CUE set 1 4
Pitch bend - 8
pitch bend + 16
Play is pression 32
Pause is pression 64
Cue is pression 128 (max pression)
There is any way to detect the value position so i can make a single button for any different position for the same value ?
i need to save my gemini's mixer
is a nice controllerit will will be so funny and cheap solution for my controller , instead of going to the trush xD
Statistics: Posted by Taysete_DJ — 01 Oct 2013, 19:07
]]>
No problem...
I was not really clear...
When I tried out with a joystick When pluggin in, Usine told me, that the joystick is ID 1 and my mouse ID 0
But it didn't work. The correct ID for the joystickwas 0. I connected a fader to the HID module (like in Nays example, but without the increment anb decrement buttons). Then when moving this fader, the console shows the connected HIDs again. And you may wonder, Now it shows Mopuse on ID2 and Joystick at ID 1.
It seems that Usine doesn't display the correct ID when pluggin in...
So maybe you give it a try again.....
If you wanna check out the messages coming from your Gemini you could try "USB Monitor".
It can be found here: http://www.hhdsoftware.com/Downloads/usb-monitor
It has a special view for HID Devices. Maybe it helps...
Thank you both , i will do more tests today , i will try all the ID's and also that software you say..I was not really clear...
When I tried out with a joystick When pluggin in, Usine told me, that the joystick is ID 1 and my mouse ID 0
But it didn't work. The correct ID for the joystickwas 0. I connected a fader to the HID module (like in Nays example, but without the increment anb decrement buttons). Then when moving this fader, the console shows the connected HIDs again. And you may wonder, Now it shows Mopuse on ID2 and Joystick at ID 1.
It seems that Usine doesn't display the correct ID when pluggin in...
So maybe you give it a try again.....
If you wanna check out the messages coming from your Gemini you could try "USB Monitor".
It can be found here: http://www.hhdsoftware.com/Downloads/usb-monitor
It has a special view for HID Devices. Maybe it helps...
Thanks
Statistics: Posted by Taysete_DJ — 25 Jan 2013, 12:38
]]>