BrainModular

hey there
i'm new here so bear with me please..

i am trying to get midi output from a midi sequencer patch in the first line
to a vsti in the second line in the same track
i have enabled rack mode but the vsti midi in registers no midi
i'm coming from more traditional DAW and i'm struggling with a few of the concepts

looking forward

dave

After trying for myself with no luck, I am assuming that midi is not routed between track lines in the same way audio is but in any case you could use a midi bus (in the Buses section of the browser) to achieve the same result. Keep in mind though that there will be a one bloc of latency when using buses to send and receive.
Or perhaps someone has a better answer?

yes, you're right gurulogic
here a wiki page about buses communication:
http://www.sensomusic.com/wiki/doku.php ... #send_midi

and welcome dave dove..

ok and what don't you use the module "send midi to usine" witch send midi signal as it came of outdoor !

I made this comparassion between midi bus/send midi to usine and direct midi out :
It seems that midi bus and send midi to usine have the same block delay

tahnks guys
will try later..

the other thing is:

in the rhombusine sequencer patch
i tried to replace the synth directly in the patch
and got nothing

i really need to get my head around this :0

dave

you have 2 ways here, using a bus system as actually ( but note that your vsti+bus can be in an other patch or track ) or directly link all the midi module to your vsti :

hey nay seven

i tried both
no sound!
strangely with aalto

something's up...

EDIT:
there is no midi leaving the sendmidibus

there is no midi leaving the create midi boxes

there is midi leaving step big and step small

i have managed to use both direct and bus midi paths with just the step sequencer module

dave

several thing you can check :

_main audio engine ON..?

_main synchro ( in the dashboard ) ON..?

_track ON..?

_Track mode..? ( if you have several patches on a track in grid mode , only the selected one is running)

audio is on
can't find synchro - is that restart synchronisation at start of cycle?
track is on
track mode: tried grid and rack

the problem seems to be inside the patches
there is no midi reaching the midi bus from the create midi boxes
in fact there is no midi leaving the create midi boxes

i can build my own sequenced synth patches from the step sequencer module...

thanks for your assistance

dave

mmm, if a step sequencer works , so synchro is ON..

is the step move on the rhombusine patch..?
if not have you check the > switch on the center..?

yes..

dave

can you test this workspace?
download

yes

that works
will test with vsti shortly

edit:

works with vsti via bus
if i insert vsti into patch
audio outs both go to same channel?

dave

And in the global setup/audio outs you have 2 different outputs ?

hey nay-seven

i'll look at that later
i'm happy now it's working and i can see how it should work
the downloaded add-on still doesn't work
do we know why?

great support by the way

dave

the downloaded add-on still doesn't work
do we know why?

no, and for info I did not change anything in the workspace I sent you, just add the track 2 .

hey

would just like to say thanks for the excellent support
i am just beginning to explore usine
i have a lot of questions
and a few issues which may or may not be my error/misunderstanding
i will explore them when i have some time and get back to you
thanks again

dave

Thanks dave !

http://soundcloud.com/reflektor-6n6p/usine-test-1

dead chuffed....

dave

Cool first track , i like it !

yeah but i got to learn to mix with this as well....
it's all mushy at the moment
i also just rebuilt this pc
and am about to upgrade the OS
so i haven't installed too many toys as yet
'cos i'll have to format the C drive anyway
running usine off a stick
also
is there a roadmap for 64bit?

dave

yes, Usine V6 is running on 64 bits, no problems
You can check this thread about roadmap